Can Bulb be Replaced on Optronics Trailer Tail Light ST33RB

Question

Question:

How do you replace the bulb in the ST33RB?

asked by: Randy C

0

Expert Reply:

I spoke with my contact at Optronics and he said that the Trailer Tail Light # ST33RB is a sonically sealed complete unit, and the bulb cannot be replaced by itself. If the bulb goes out, replacing the entire light with a new # ST33RB will be your only option.

expert reply by: Robin H

0

Answer 1

For your Optronics light part as2t216 we have found that the correct replacement lens is the part #AST60B. Normally the SAE number isn't a reliable way to find lens replacements as it's not a part number but we do know that this SAE number…

view full answer...

Answer 2

Yes, the LED light part #STL35RB can be used to upgrade the lights in a Thule Transporter Hitch Mounted Cargo Carrier part #TH665C. I went out to the warehouse and test fitted the LED lights inside the original grommet that comes with the Transporter…

view full answer...

Answer 3

The replacement tail light for the Thule Terrapin cargo box is #TH05252. This is an incandescent light. There isn't an official LED light made for it but you could potentially use #STL35RB. It measures 5-5/16 inches by 3-7/16 inches and is 2-5/16…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can Bulb be Replaced on Optronics Trailer Tail Light ST33RB

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching