Replacement Entry Door Locking Latch For Travel Trailer

Question

Question:

I am looking for a replacement entry lock for a pull behind travel trailer the cutout is 4 7/8 x 4 3/8 x 1 1/2 The door is hinged on the left. The trailer was made by Holiday Traveler

asked by: Jim W

0

Expert Reply:

We have what you need.

Bauer Products Motorhome Door Lock - Black # BA64FR.

I recommend the Bauer door lock. It can be keyed alike to match other Bauer items and will fit your door.

expert reply by: David B

0

Answer 1

We have a very similar entry door lock with the Bauer Products Camper Door Lock #BA65FR. The configuration appears to be very similar to the lock on your 2004 Featherlight horse trailer. The Bauer lock is made to fit a cutout 5-1/4" wide x…

view full answer...

Answer 2

The difference between an 18:1 and 55:1 ratio is going to be the amount of times the smaller gear has to rotate to turn the larger gear one time. So for example your current 28:1 has to rotate 28 times to turn the larger gear one time. You will…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Thanks for the picture! I checked with Progressive Dynamics the replacement power converter you need for your Parallax Series 7300 Model 7345 is the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers - 45 Amp item #PD4645V.

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Entry Door Locking Latch For Travel Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching