Replacement Diverter Pin Assembly Plastic Bracket Dimensions

Question

Question:

Phoenix Faucets Accessories and Parts - PF182012 I need to know the length and width of the small white plastic piece or valve before I order. It is square-ish. Thank you,

asked by: Edward S

0

Expert Reply:

I went out to the warehouse and measured the white plastic bracket you mentioned, and from flat end to end measures 1-1/16" and the angled edge side from end to end, measures 1".

The inner circle has an inner diameter of 3/4", and an outer diameter of 7/8".

expert reply by: Bryce D

0

Replacement Diverter Pin Assembly Dimensions Dimensions
(click to enlarge)

Answer 1

The correct replacement for your Klauber K01431B300 slide-out motor is the Replacement Motor Assembly for Lippert RV Slide-Outs - Klauber A-300 Model #LC157511.

view full answer...

Answer 2

The proper replacement for your Klauber A300 series K01336A300 would be the Lippert #LC157511. My Lippert representative has confirmed that this is the correct replacement.

view full answer...

Answer 3

We do have the replacement motor that you need for your slide-out. To replace your Klauber K01405A300 slide-out motor, you will want to use the Replacement Motor Assembly for Lippert RV Slide-Outs - Klauber A-300 Model #LC157511. I am not aware of a…

view full answer...

Answer 4

Hi Myles; for a replacement switch you can use the Single Slide-Out Momentary Switch #37212295. This fits a 1.85" tall x 1.20" wide cutout (1.85" wide x 1.20" tall installed horizontally) so I would double check those dimensions.…

view full answer...

Answer 5

The two smaller black wires on the Replacement Motor Assembly for Lippert RV Slide-Outs - Klauber A-300 Model #LC157511 are for the motor brake release and engage. Without connecting them the motor will not properly function. One wire will need to be…

view full answer...

Answer 6

Since your 2022 Ford Transit T-350 High Roof Extended Length is available in either a singe wheel rear axle or a dual wheel rear axle you will need to choose the correct 7-way harness. For a single rear wheel axle the Tekonsha OEM Replacement Vehicle…

view full answer...

Answer 7

Hello Bill. Looking thru all of the manufacturer's literature on this Klauber K012850300 motor, they do not list a specific strength for the sheer pin. Replacement parts are generally just linked to the motor assembly itself and those kind of…

view full answer...

Answer 8

I went ahead and found a wiring diagram for the Single Slide-Out Switch #37212285, and you are going to need to just match the hot from your trailer to the power (+) pin, and then match the green and blue wires to the motor (+) pins. I have attached…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Diverter Pin Assembly Plastic Bracket Dimensions

Product Page this Question was Asked From

Continue Researching