Replacement Hubs With 5 on 5 Bolt Pattern for M116A3 Trailer
Updated 07/26/2025 | Published 02/25/2022
Products Featured in This Question
Question:
I have a m116a3 axel military trailer. It currently has the 8x6.5 bolt pattern hubs. I want to keep the original axel I don’t want to do a full axel swap. Im look to just do a hub swap to a 5x5 bolt pattern. Is this something that can be done?
asked by: Zach
Expert Reply:
This is possible assuming the bearings match up with the spindle on your current axle. All of our idler hubs and hub and drum assemblies with a 5 on 5 bolt pattern use a # L44649 outer bearing and # L68149 inner bearing. You will need to either find the part numbers on the existing bearings or measure your spindle to see what you have.
Assuming these match up we have several options. If you are looking for a hub and drum assembly we have the # AKHD-550-35-K or the # AKHD-550-35-EZ-K for E-Z lube axles. If you just need an idler hub then we have the # 84550BX or the # 84550UC1-EZ for E-Z lube axles.
I have attached some review videos along with a helpful diagram showing the location of part numbers and where to measure a spindle that you can check out.
(click to enlarge)
Product Page this Question was Asked From
etrailer Rubber Hitch Cover for 2" Trailer Hitches - Qty 1
- Hitch Covers
- Misc Covers
- Plain
- Rubber
- Fits 2 Inch Hitch
- Standard
- Square
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Video: Let’s Check Out the Trailer Idler Hub Assembly for 3,500-lb Axles
- Shop: Timken Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased
- Video: Hands-On with the Trailer Idler Hub Assembly for 3,500-lb Axles
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Search Results: hub
- Search Results: trailer axle
- Q&A: Which is Better an EZ Lube Spindle or a Bearing Buddy Setup
- Shop: Progressive Dynamics Replacement Section for AC/DC Power Distribution Panel - 45 Amp
- Shop: Go Power RV Converter and Smart Battery Charger - 12V - 35 Amp
- Shop: Progressive Dynamics 9300 Series RV Converter Charger - 12V - 30A
- Search Results: lubricants sealants adhesives
- Search Results: converter
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Q&A: Can 2017 Lance 1475 Battery Bank Be Upgraded to Lithium Batteries
- Q&A: Trailer Hub Grease Seals Need to be Greased before Install
- Q&A: Trailer Hub Availability with 5 on 4-1/2 inch Bolt Pattern
- Q&A: Video Showing How to Install a Grease Seal on a Trailer Hub
- Q&A: Differences Between Trailer Idler Hubs With a 5 on 5 Bolt Pattern
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: 7-Piece Installation Set for Bearings, Races, and Seals
- Search Results: bearing buddy trailer bearings races seals caps
- Search Results: bearing buddies
- Search Results: trailer hub
Robert M.
7/24/2025
I am not sure if this was ever answered. I am trying to find a drum to fit the same trailer and would love some help. I would prefer a 6x5.5 or 8x6.5 bolt pattern but have not found a drum that works with this spindle.