Replacement Lens for Optronics MC32RB and MCL32RB Trailer Lights

Question

Question:

What # is the # A32RB for the amber lense ?

asked by: Terry C

0

Expert Reply:

Hi, this is a snap-on red lens that replaces a damaged Optronics clearance or side marker light, it fits the MC32 and MCL32 series lights. It is 4" x 2". Please note the link for product review video.

expert reply by: Michael R

0

Answer 1

Hey Steve, hope you are well! Unfortunately, we do not offer a replacement rod, screw and nut for the #TJA-2000S-B jack. We have replacement gears, but the rod and nut are not available as a replacement part. I wish we did because then I could go…

view full answer...

Answer 2

The longer 2-1/2" torx screw Item #TFX250ACQ will work the best to attach the boards to the metal frame of your Big Tex trailer when replacing the trailer deck. If you need a torx head screwdriver bit, you can use part #TX430-1.

view full answer...

Answer 3

The hub you have is a 3,500 lb idler hub that has a 5 on 5 inch bolt pattern so you'd want the part #AKIHUB-550-35-K and you'd be set! This comes with bearings, lug nuts, a grease seal, and a grease cap/dust cover. Or, we have the part…

view full answer...

Answer 4

You can confirm the weight rating of your Dexter axle by removing one hub and pulling its bearings. The included photo shows how part numbers usually appear on bearings. The specific bearings used will tell you the axle's weight rating. Just…

view full answer...

Answer 5

This is possible assuming the bearings match up with the spindle on your current axle. All of our idler hubs and hub and drum assemblies with a 5 on 5 bolt pattern use a #L44649 outer bearing and #L68149 inner bearing. You will need to either find…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement Lens for Optronics MC32RB and MCL32RB Trailer Lights

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching