What is the Backspacing of the 14" Dexstar Conventional Steel Wheel

Question

Question:

Can you tell me the exact backspacing ?

asked by: Michael

0

Expert Reply:

The backing spacing of the Dexstar Conventional Steel Wheel part # AM20304 is 3.25" plus the lip for a total of 3.50". The wheel is 5.50" wide with a .50" offset which is what you use to determine backspacing.

expert reply by: Conner L

0

Answer 1

You can pretty easily go from a 205/75-14 to a 15 inch tire size like 205/75-15 like with the #AM32395 without clearance issues. This will give you a slightly larger wheel and tire which will have a higher weight capacity. So you might gain a slight…

view full answer...

Answer 2

Hello Steve, thanks for reaching out. The Kenda tires are made in China like most other trailer tires. As far as the Kenda Karrier KR53 ST205/75R14 Radial Trailer Tire with 14" Black Mod Wheel #KE75EV, the wheel itself is made here in the USA,…

view full answer...

Answer 3

Great question, William! The Karrier ST225/75R15 #KE63KV is a KR35 while the Karrier ST225/75R15 #AM10303 is a KR03 according to Kenda. There is a slight variation in the tread pattern and from what Kenda says about them it looks like the KR03 is…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What is the Backspacing of the 14" Dexstar Conventional Steel Wheel

Product Page this Question was Asked From

Continue Researching