Dimensions for the Replacement Wooden Toilet Seat

Question

Question:

What is the inside dimension of the hole front to back and side to side? asking for this on product Dometic Toilet Seat part # DOM25FR

asked by: Larry`

0

Expert Reply:

I went out to our lot and found an RV with the Replacement Wooden Toilet Seat and Lid for Dometic Full-Timer RV and Sealand Toilets item # DOM25FR and took some measurements. The inside dimensions of the seat are 8-1/4" x 10-7/8". I have attached a diagram.

expert reply by: Jerred H

0

Dometic Toliet Seat Dimensions
(click to enlarge)

Answer 1

You are correct that the original part has been discontinued. The replacement seat #DOM25FR (385343831) is going to be your best bet. It looks like your current seat is about 14" or 14-1/2" across and about 16" long. The replacement…

view full answer...

Answer 2

Hey Ron, I am not sure if you meant to type model 4310 or just 310. I am not familiar with a 4310 model but I do know we carry a replacement for a 310 model. That part number is #DMC22YR. That would be a direct replacement for the 310 model. If you…

view full answer...

Answer 3

There's a good chance you have a Dometic RV toilet which I attached a picture that has all of the styles shown with the numbers that they correlate with. Check out what you have and compare to the picture and I'll see which replacement seat…

view full answer...

Answer 4

The overall length of the seat of Dometic RV Toilet Seat #DOM83FR is 15 inches on the outsides and 11 inches on the inside of the opening. The inner width is then 8 inches. This is a confirmed fit for your Dometic 310 model as well.

view full answer...

Answer 5

We have what you need in the Replacement Wooden Toilet Seat with Slow Close Lid for Dometic Part-Timer RV Toilets, #DOM83FR. This fits the Dometic 310 series RV Toilet, #DOM57FR. What you linked to is the replacement for Dometic Full-Timer, #DOM85FR…

view full answer...

Answer 6

The Dometic Replacement Toilet Seat #DOM85FR measures 5-1/2" center to center of the mounting holes, 15" wide, and 18" long as you can see in the included diagram. I included a video of the #DOM85FR for you to take a look at.

view full answer...

Answer 7

The lid for the Replacement Wooden Toilet Seat #DOM83FR that fits on a Dometic 310 RV Toilet #DOM57FR tapers to be narrower at the top of the lid. So it will be slightly narrower than the seat itself. I have included dimensions that show the widest…

view full answer...

Answer 8

I'll go ahead and list out the options for you for replacement toilet seats for Dometic RV toilets, but we have no way of knowing what toilet is any specific trailer, so you'll have to match up yours with the correct replacement. - Dometic…

view full answer...

Answer 9

Thanks for the pictures of your 500 series Dometic RV toilet. The part #DOM85FR you referenced will fit and work great as an exact replacement.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Dimensions for the Replacement Wooden Toilet Seat

Product Page this Question was Asked From

Continue Researching