Tips for Installing Trailer Taillight with Grommet

Question

Question:

I have the 337LB6123SST double 4inch mounting box along with STL101RMB 4inch GloLight and A45GB grommet. The grommets fit nicely in the box but the light will not fit after the grommet is in place. It is incredibly tight. Have I purchased something incorrect?

asked by: Justin P

0

Expert Reply:

The grommet part # A45GB that you referenced is correct for the trailer taillight part # STL101RMB that you have. Grommets and lights can be difficult to install but the way to do it is install the light into the grommet first and then push the assembly into the hole. You can use hand soap on the grommet to help get it to slip into place as well.

expert reply by: Jameson C

0

Answer 1

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 2

LED lights are diodes so if you were to wire them backwards on accident they just wouldn't light up. There would be no damage at all.

view full answer...

Answer 3

The difference between the letter D in your ST175/80D13 and the R in the tire size of the Wheel and Tire ST175/80R13 part #AM31985 that you referenced is the tire construction. D stands for bias-ply which is a less preferred tire construction,…

view full answer...

Answer 4

Mike, it sounds like you're looking for the Triplex Wire with Grey Outer Jacket #SWC5362-1 which is jacked 14 AWG 3 wire. Also, this is sold per foot, so if you needed 10 feet you'd need to order 10. If you're looking for something else,…

view full answer...

Answer 5

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 6

Hey Jay, spec-wise the two tires are exactly the same and are even made by same company. Only real difference is a slightly different tread pattern so I would go with the better priced part #KE68KV all day.

view full answer...

Answer 7

The light dimensions of the Optronics LED #TLL12RK are 7-9/16" long x 2-3/4" tall x 1-3/4" deep and the hole size needed is 6.75" by 2.5 inches. I confirmed this with my contact at the manufacturer and I've attached a template…

view full answer...

Answer 8

It sounds like you are wanting to replace your incandescent backup lights on your kayak trailer with LED lights like the Optronics LED Backup Light for Trucks or Trailers #BUL52CB. If that is the case, all you will need to do is replace the current…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...