How Much Do Torklift Tie Downs TLF2023 Weigh

Question

Question:

What is the weight of this pair of brackets?

asked by: Mike

0

Expert Reply:

The weight of F2023 Tork Lift Tie Down # TLF2023 weighs roughly 30 pounds per set.

expert reply by: Bryce D

0

Answer 1

The S-Hooks #37201154 are rated at 4,500lbs for the safe working load.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

Hello Barry, Since you already have a weight distribution (WD) hitch and are only experiencing a little rear sag, I recommend going with SumoSprings. I typically only suggest Timbrens for those who are towing heavy loads regularly, as they can create…

view full answer...

Answer 6

Hey Gary. The Draw-Tite Front Hitch item #65031 is going to mount a bit higher on your 2004 Toyota Tundra compared to the Curt item #31180. The Curt Front Hitch item #31180 is 14-3/4" off the ground when measured from the top of the inside of…

view full answer...

Answer 7

Hey Lexie, the closest thing we have is the #BA65FR. This fits cutouts that are 5-1/4" wide x 4-1/2" tall. The little bit of extra height on your cutout won't be a problem since the face is 5-1/2" tall and would cover the opening.…

view full answer...

Answer 8

The upper bracket part #AL07475 that you referenced is a fit for your 2003 Ford F-250 as this bracket is part of the kit part #AL57215 which is a fit for your truck.

view full answer...

Answer 9

We do carry some nice heavy duty rubber plugs to protect the factory prep package on a Chevrolet Silverado. For this, you can use the Rubber Hole Cover part #RP30136 for the gooseneck hole and the Puck Plug Covers part #58199 for the pucks.

view full answer...

Answer 10

Hi Robert, welcome back! Are you referring to the manual override handle for the Bulldog Powered-Drive Trailer Jack #BD500188? Assuming that is correct, you need the Replacement Manual Override Crank for Bulldog Powered-Drive Trailer Jacks #BD500203.…

view full answer...

Answer 11

If you are referring to the inside diameter of the socket head on the Replacement Manual Override Crank for Bulldog Powered-Drive Trailer Jack part #BD500203 then that is 1/2"diameter. The diameter of the handle portion is also 1/2". If…

view full answer...

Answer 12

Hello Bart, thanks for reaching out. I can definitely point you in the right direction, but I will need a bit more information on your truck before I can recommend the correct tie downs. Can you please answer the following questions for me? 1. What…

view full answer...

How Much Do Torklift Tie Downs TLF2023 Weigh

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching