Solution for Pulling Hub/Drums Off of Trailer Spindle that Seem Stuck

Question

Question:

Hi! I’m looking to replace the brakes on my Airstream with these and getting a feel for if I can manage the job. I’ve pulled the snap rings and the nut on the hub and the drum pulls off about 1/4” and then gets stuck. It seems like the pads have worn in enough to catch the drum and not let it pop off. Can these brakes be adjusted like normal drum brakes to retract them and pull off the drum or am I missing something? Thanks for the help!

asked by: Kurt S

0

Expert Reply:

You need to manually adjust your brake assemblies to bring the pads in so that you can pull the drum off.

To see how to manually adjust trailer brake assemblies check out the video I attached, fast-forward to the 4:35 mark of the video. For an adjuster you could use the brake adjustment spoon part # W80630.

I also attached an install video for this brake assembly set for you to check out as well.

expert reply by: Jameson C

0

Answer 1

Sounds like the brake assembly you are installing on your trailer has the pads adjusted too far. On the bottom of the assembly there will be a star wheel that you can turn in either direction. You will want to turn it so that the brake pads come…

view full answer...

Answer 2

It sounds like your trailer brakes are sticking, but I doubt the problem is the brake controller. However, you can test this by applying the brakes like you normally do while coming to a stop. Once the trailer and vehicle stop get out and unplug your…

view full answer...

Answer 3

It can certainly be tough to remove a stuck hub. There really isn't a tried and true method to get your hub off, particularly if yours somehow got hot enough that it basically welded itself to your spindle. I would use a bunch of WD-40 and just…

view full answer...

Answer 4

If you're having trouble removing the hub/drum, you'd first want to start at the rear of the assembly with the brake adjuster screw. In order to help the hub slide off the brakes, loosen the star wheel (turn counter-clockwise) a few turns to…

view full answer...

Answer 5

You can cut off the old spindle and have an EZ-Lube spindle welded on your current axle. I would recommend using the same size spindle, just the EZ-Lube version, as your trailer originally came with. That being said, new hub assemblies and bearings…

view full answer...

Answer 6

The first thing to try to is add some penetrating oil like WD40 and let it sit for awhile. You can then try tapping the bearing to try and remove it. You don't want to hit it too hard because you can damage the spindle. It is possible that the…

view full answer...

Answer 7

We have an option that will work exactly how you are wanting. I recommend the Snap-Top Battery Box with Strap for Group 24 to Group 31 Batteries - Vented #329-HM318BKS which can be mounted to the tongue of your trailer and would be perfect for…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Solution for Pulling Hub/Drums Off of Trailer Spindle that Seem Stuck

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching