Receiver Hitch Weight for a 2021 Ford EcoSport

Question

Question:

How many kg does the product weigh? Draw-Tite Class II Frame Receiver Hitch - 2021 Ford EcoSport

asked by: Mr L

0

Expert Reply:

The Draw-Tite Trailer Hitch Receiver item # 36660 for a 2021 Ford Ecosport weighs 32 lbs or 14 1/2 kg.

expert reply by: Jerred H

0

Answer 1

Hey Pam, so the highest rated 1-1/4 inch to 2 inch hitch adapters we offer have a 350 lb tongue weight capacity like with the part #e43YR for a straight adapter or the part #e93YR for one with a rise built into the shank. You have to keep in mind…

view full answer...

Answer 2

The Draw-Tite Trailer Hitch Receiver #36660 will fit your 2018 Ford EcoSport SE no matter what size engine you have so you are good to go on that end of things (plus the EcoSport in the video is an SE). The hitch comes will all of the hardware to get…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

No, it will not Bryan. The Redarc Tow-Pro Link item #RED57AR requires a USCAR port that comes with factory tow packages. The Stealth Hitches Hidden Trailer Hitch Receiver w/ Towing Kit item #SH25VR, that fits your 2023 BMW X5, does not have this…

view full answer...

Receiver Hitch Weight for a 2021 Ford EcoSport

Continue Researching