Trailer Brake Hookup Location On A 2012 Ford F-250/350

Question

Question:

For the hookup for the brake controller is it in the same spot for the 2012 f250 as the f350

asked by: Joe T

0

Expert Reply:

Yes, the location to plug in # 3034-P for the 2012 Ford F-250/F-350 should be in the same spot; behind the coin pocket in the center of the dash.

expert reply by: Bryce D

0

Trailer Brake Controller Location
(click to enlarge)

Answer 1

Typically the brake control port that allows connection of an aftermarket trailer brake controller on the 2012 F-250 is located behind a small dashboard panel slightly to the right of center (toward the passenger side). Please refer to the photo…

view full answer...

Answer 2

The error code you are reading indicates that there is a short circuit somewhere in the brake outupt circut on your trailer. Most likely, there is a pinched wire or at some point the wire insulation has cracked or been worn to the point where the…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 6

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

Hey David, it sounds like you know what you're doing but I've also gone ahead and found the wiring diagram for the Replacement Single Zone Thermostat for Dometic RV Air Conditioners #DMC79FR for you to check out so you can use it as a cross…

view full answer...

Answer 12

Hi Jeff, welcome back and sorry to hear that gave you so much trouble. The Redarc Tow-Pro Link Bluetooth Brake Controller #RED57AR will work on your Silverado. This plugs in-line at the back of your 7-way at the rear of the truck. You can either…

view full answer...

Trailer Brake Hookup Location On A 2012 Ford F-250/350

Featured Help Information

Miscellaneous Media

Continue Researching