Should The Charge Wizard Be Removed When Switching Progressive Dynamics AC/DC Panels To Lithium Mode

Question

Question:

When switching over to lithium battery mode do you need to remove the four wire harness that connects the wizard on the circuit board?

asked by: Richard G

0

Expert Reply:

Once you flip the switch to lithium on your Progressive Dynamics RV Power Control Center with AC/DC Panel and Converter/Smart Charger - 35 Amp # PD4135K it basically bypasses the Charge Wizard # PD92201 so you can remove it or leave it connected.

expert reply by: Kevin C

0

Answer 1

Hey Gary! Tekonsha is for sale right now and their parts like the P3 and custom wiring harness aren't currently available. As an alternative, I recommend the Redarc Tow-Pro Liberty Brake Controller #RED96CR. The Liberty is just as reliable as the…

view full answer...

Answer 2

It sounds like your Valley-brand Phantom brake controller has seen better days. Since they are no longer in business even if the unit were repairable parts and authorized service are not, so your best option is a new controller. In most cases a…

view full answer...

Answer 3

In regards to the Progressive Dynamics Inteli-Power RV Converter and Battery Charger part #PD9160ALV, there will be no issues using this on a lithium (LiFePO4) battery with integrated BMS. The BMS is just there for protection but since the converter…

view full answer...

Answer 4

The port that the #PD92201 remote pendant plugs into is located on the side of the #PD9245C unit as shown in the provided photo.

view full answer...

Answer 5

The Progressive Dynamics Inteli-Power RV Converter and Battery Charger - Lithium - 24V - 40 Amps #PD914024ALV will fully charge your battery bank but it doesn't have different stages of charging. Unfortunately there aren't any other options…

view full answer...

Answer 6

Hey Gary, thanks for the information. Since you've upgraded to LiFePO4 batteries, I recommend upgrading your converter to the Progressive Dynamics 9300 Series RV Converter Charger item #PD79RR. This delivers 60 amps of DC charging power at 14.6…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Should The Charge Wizard Be Removed When Switching Progressive Dynamics AC/DC Panels To Lithium Mode

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching