How Long are the Screws in Replacement Hardware Bag for Yakima LandingPad 1 # 8890028

Question

Question:

What size are the bolts?

asked by: Craig C

0

Expert Reply:

I spoke with my contact at Yakima on replacement hardware bag # Y8890028. The bolts are M6x20. The 20 is millimeters so they are 20 millimeters long. This is a little over 3/4 of an inch.

expert reply by: Michael H

0

Answer 1

I called my contact at Yakima about the bolt you need for the Landing Pad. The bolt is not sold as an individual item and it is not included in a replacement C Plates for Landing Pad 5. They are included with the hardware bag for LandingPad 1, part…

view full answer...

Answer 2

The screws and plates of the Replacement Hardware Bag for Yakima LandingPad 1 #Y8890028 are made of steel that is zinc coated.

view full answer...

Answer 3

To mount Yakima SkyLine towers in your UltraGroove the foot pack is the Landing Pad 1 for Yakima SkyLine and Control Towers #Y00221, and the correct replacement hardware with the T-slot nuts and bolts for this foot pack is the following: -…

view full answer...

Answer 4

Yes, the Replacement Anchor Plate "A" for Yakima LandingPad 1 #Y8810074 is the same anchor plate that is in the Replacement Hardware Bag for Yakima LandingPad 1 #Y8890028. For the bolts #Y8890028 does come with 4 of the corresponding M6 x…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

How Long are the Screws in Replacement Hardware Bag for Yakima LandingPad 1 # 8890028

Product Page this Question was Asked From

Continue Researching