Replacement Bolt For C Plates Used With Yakima Landing Pad 5

Question

Question:

Looing for the bolt that fits the Yakima plate c for securing Yakima landing pad to factory roof rack track. I sheared one off after it cross threaded.

asked by: Andrew B

0

Expert Reply:

I called my contact at Yakima about the bolt you need for the Landing Pad.

The bolt is not sold as an individual item and it is not included in a replacement C Plates for Landing Pad 5. They are included with the hardware bag for LandingPad 1, part # Y8890028.

If you do not want to buy the entire kit you can visit a local hardware store and the bolt is M6 x 20.

expert reply by: Jeffrey L

0

Answer 1

The plates of the #Y10156 are steel and 1/8 inch thick.

view full answer...

Answer 2

The Yakima Replacement Anchor Plate Style-A, Part #Y8810074, comes as a set of 8 plates that measure 3/4-inch x 7/8-inch. The centered threaded hole measures 0.2 inches (or 5.1 millimeters) in diameter. Please refer to the photo provided. The Yakima…

view full answer...

Answer 3

I spoke with my contact at Yakima on replacement hardware bag #Y8890028. The bolts are M6x20. The 20 is millimeters so they are 20 millimeters long. This is a little over 3/4 of an inch.

view full answer...

Answer 4

The difference between Landing Pad 1 #Y00221 and Landing Pad 4 #Y00224 is the hardware. For LP1 the 'A' plate dimension is 7/8" x 11/16" and for LP4 the 'C' plate dimension is 1 3/16" x 13/16" so they fit different…

view full answer...

Answer 5

Yes, the Replacement Anchor Plate "A" for Yakima Landing Pad 1 #Y8810074 will fit the Yakima rails on your A.R.E. truck bed camper. Please note that these are meant to be used with the Yakima Landing Pad 1 feet so it may not fit your…

view full answer...

Answer 6

Yes, you can absolutely mount your Thule Hullavator Pro Kayak Carrier #TH898 into the T-slot channels of the Yakima HD crossbars. The HD crossbars are available in the following sizes: - 55" Long: Yakima HD Crossbars #Y01156 - 60" Long:…

view full answer...

Answer 7

I recommend picking up the Aero Style Crossbar T-Slot Fit Kit #MPG8287 which comes with bolts, nuts, and washers that will fit in the Yakima HD Bar T-Slots like the 78" part #Y01159. If you're trying to find specific dimensions for your own…

view full answer...

Answer 8

The T-slot channel dimensions for the Yakima HD Crossbars #Y01158 are 11mm (7/16") wide on top, 8mm(5/16") deep, and 22mm(14/16") wide at it's bottom. I attached a picture of the HD crossbar's diagram as well as a video with…

view full answer...

Answer 9

The Yakima HD Crossbars #Y01159 have a 3/8" opening on the top of the bar which is 1/4" tall and 13/16" wide inside the slot opening. This will accept both the Replacement T-Bolt with Nut for Yakima Rack and Roll Trailers #Y8880184 and…

view full answer...

Answer 10

Malone AirFlow roof racks like #MPG215 can use their own T-Slot Fit Kit #MPG8287 for Malone carriers or you can use another T-bolt fastener. I linked a photo showing a cross section of the AirFlow bar and the exact inside dimensions. I converted the…

view full answer...

Answer 11

view full answer...

Answer 12

Yes, the Replacement Anchor Plate "A" for Yakima LandingPad 1 #Y8810074 is the same anchor plate that is in the Replacement Hardware Bag for Yakima LandingPad 1 #Y8890028. For the bolts #Y8890028 does come with 4 of the corresponding M6 x…

view full answer...

Replacement Bolt For C Plates Used With Yakima Landing Pad 5

Products Featured in This Question

Continue Researching