Wiring Diagram for Superwinch LT4000 ATV Winch

Question

Question:

I purchased an Lt4000 ATV winch with a remote control switch. Can I download the wuring diagram for both?

asked by: Patrick G

0

Expert Reply:

I'd be more than happy to help you out! Attached is a wiring diagram for the Superwinch LT4000 ATV Winch # SW1140220. We don't have the instructions available as a download, but when I reached out to my contact at Superwinch they were able to provide me with the image I mentioned.

expert reply by: Jon G

0

Wiring Diagram for Superwinch LT4000 ATV Winch
(click to enlarge)

Answer 1

I was able to find a wiring diagram for the Superwinch ATV A3500 winch that you have. I also attached a link to the install instructions for this winch in a separate email.

view full answer...

Answer 2

I attached a diagram that shows how the Superwinch part #SW1130220 gets wired up. In it you can see which terminal you would need to run the black and red wires. Is the battery you are using fully charged? What you described is typically the sound of…

view full answer...

Answer 3

For starters, the correct replacement switch for the Superwinch LT2000 ATV Winch 1120210 is the Replacement Rocker Switch part #SW2320200. I have attached a wiring diagram of the correct switch for you below as well as the text from the manual. Route…

view full answer...

Answer 4

The replacement rocker switch for the Superwinch Terra Series ATV Winch part #SW1145220 is the Replacement Controller for Superwinch Terra Series ATV Winch part #SW87-42609. I have attached the wiring diagram of this rocker switch for you as well.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Wiring Diagram for Superwinch LT4000 ATV Winch

Product Page this Question was Asked From

Continue Researching