Recommended Disc Brake Kit to Convert From Electric Brakes on 1984 Fleetwood Terry Travel Trailer
Updated 11/23/2021 | Published 11/22/2021 >
Products Featured in This Question
Question:
Hi, I have an 1984 Fleetwood Terry 28 foot travel trailer with tandem axles. Looking to convert the existing drum brakes with a one piece hub and rotor setup like this. I have no documentation for the trailer, but am certain the existing axles, hubs, drums, and wheels are OEM. The wheels are 15” and bolt pattern is confirmed a match. I’m concerned about whether I can make any assumptions about this assembly and matching bearings fitting the spindles on my axles. I have no idea if they are 3500 or 3700, but it looks like these will fit either size. Do I need to pull a hub and measure a spindle, or can I safety assume these would be a match?
asked by: Brian N
Expert Reply:
In order to make sure you get the right brake kit I would not make any assumptions. It would be best to go ahead and pull the hub and take measurements just to be safe. See the helpful diagram below if you aren't sure where to measure. I recommend using a digital caliper like the # PTW80157 to take your measurements. It is possible that you could find part numbers on there but I'm guessing they have worn off.
Once you have you have your measurements you will be able to find the correct bearings which will allow you to choose a disk brake kit. You will need a whole kit like the Kodiak Disc Brake Kit - 10" Hub/Rotor - 5 on 4-1/2 - Dacromet - 3,500 lbs # K2HR35D. This uses a # L68149 inner bearing and # L44649 outer bearing with a # RG06-050 grease seal. You will need 2 of these on order to add brakes to both axles.
You will also need a brake line kit and a hydraulic disc brake actuator to complete the setup. For tandem axles, I recommend the Titan Hydraulic Brake Lines and Fittings for Tandem-Axle # T4830000. For an actuator, you need to choose one that is designed for hydraulic disc brakes (as opposed to drum) and meets or exceeds your gross trailer weight rating. Ideally you want it as close as possible for the brakes to work as they should. An actuator like the Dexter DX7.5 Drop-N-Go Brake Actuator # 099-175-20 has a 7,500 lb capacity and fits a 2" ball.
I have attached some review and installation videos for your reference. I also attached a helpful article on adding hydraulic disc brakes to a trailer and a link to all of our hydraulic disc brake actuators that you can check out.
Product Page this Question was Asked From
Dexter 10" Hub-and-Rotor Assembly - 5 on 4-1/2 - Zinc - 3,500 lbs
- Trailer Hubs and Drums
- Hub with Rotor
- Standard
- L68149 / L44649
- Marine Grade
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Q&A: Replacement Hub/Rotor for UFP 41030
- Q&A: Replacement DB35 Disc Brake Assembly
- Q&A: Replacing Older Tie Down Engineering 46210 and 46845 Trailer Hubs
- Q&A: What Bearing Kit and Replacement Parts for My Dexter Vault do I Need for 3,500 Axle Skeeter Boat?
- Q&A: Replacement Hub/Rotor and Bearings for Tie Down Engineering TDE46245
- Q&A: What Inner and Outer Bearings Does 3,500 lb Axle Disc Brake Kit Use
- Q&A: Which Caliper Should Be Used With The Dexter 9-3/4" Hub-and-Rotor Assembly DX82UR?
- Article: How to Bleed Your Trailer Surge Brakes
- Article: Trailer Wiring Diagrams
- Article: Most Popular Wheel Bearings
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Article: Hydraulic Trailer Brakes: How They Work & What to Buy
- Article: How To Measure And Replace Everything In Your Hub Assembly
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)






