Hardware Kit For A Demco Cast Head Coupler.

Question

Question:

Do you sale the hardware the bolts for installation?

asked by: Todd

1

Helpful Expert Reply:

I have a solution for you. We do not carry hardware kits for the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K # DM37ZR. However the instructions will give you the dimensions you will need and you can pick them up from any hardware store.

expert reply by: David B

1

Answer 1

The only differences between the Demco eZ-Latch Couplers #DM37ZR and #DM14793-81 is that the former has integrated loop holes for installing safety chains and a about a 2" drop while the latter doesn't come with provisions for attaching the…

view full answer...

Answer 2

To install the P2 part #90885 in your 2003 Chevy Tahoe will require the install harness part #3015-P. I attached an install video and help article that will walk you through the process. There are a couple under hood connections that will also need…

view full answer...

Answer 3

The Demco Cast Head Coupler eZ Latch #DM37ZR coms as the coupler only so you would need to supply the mounting hardware. You will need 1/2" bolts that are at least Grade 5 rated. Anything higher than that will just be even stronger and work just…

view full answer...

Answer 4

While we do not carry trailer frames we do carry all the other parts you are going to need to build your tear trailer. I have compiled a list of parts that you can use to build a 3,500lb GVWR Trailer. Trailer Axle with Idler Hubs #e72GR Single-Axle…

view full answer...

Answer 5

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 6

Hello Stephen, I am always looking for a good excuse to stretch my legs (thank you), so I went out and got the measurement you requested, from the top of the bolt hole, to the bottle of the rail on the #DM37ZR is 1 9/16". I attached an image of…

view full answer...

Answer 7

Hi Torree! Thanks so much for the beautiful photo of your Entegra Coach. What a great-looking setup! To answer your question: the Yakima EXO Swing Away Cargo Carrier part #Y72VR isn’t rated for use on the back of a motorhome. That’s because it hasn’t…

view full answer...

Answer 8

The Demco A-Frame Trailer Coupler part #DM14793-97 is designed for a standard a-frame trailer with a 50 degree angle. This is the most common type so there really shouldn't be any other issues that affect fit. That said, I have attached some…

view full answer...

Answer 9

That is correct the inner dimension of the Demco A-Frame Trailer Coupler item #DM14793-95 is 10 3/4 inches. I have attached a picture that breaks down the measurements. You would need to fabricate a spacer on either side to attach this coupler to…

view full answer...

Answer 10

Hey Bob, thanks for the information. It looks like you have a 3,500 lbs axle with a 86.5" hub face and a 68.5" spring seat. The only axle I have with a 86.5" hub face is the 5,200 lbs Capacity Trailer Axle Beam with Easy Grease…

view full answer...

Answer 11

I do have an option for you but latch repair kits are coupler specific and there are very few out there. Furthermore, the Lippert 2" Latch Coupler Repair Kit 678750 is no longer available and I know this isn't what you want to hear but the…

view full answer...

Answer 12

Hey Rylan, I checked with Demco for you, and the Demco A-Frame Cast Head Coupler #DM37ZR will need Grade 5 hex bolts for installation. We don't have these but they can be found at any local hardware store.

view full answer...

Hardware Kit For A Demco Cast Head Coupler.

Product Page this Question was Asked From

Continue Researching