Swivel Trailer Jack that Can Fit on 2.5 inch Snap Ring

Question

Question:

Hi I have the following swivel trailer jack that gave out, see attached pictures. It attaches to the trailer via a snap ring. Trying to determine if this jack would be a good replacement or do you have a better suggestion. snap ring diameter is 2.5 inches

asked by: Tim R

0

Expert Reply:

The Fulton Round Snap-Ring Swivel Marine Jack part # FTJ12000101 has the same 2.5" snap ring dimension and will work out for you as a direct replacement.

expert reply by: Jameson C

0

Answer 1

The Dutton Lainson Pull Pin, Easy Swivel Trailer Jack #DL22560 referenced in your question is designed to fit a 2-1/2 inch diameter weld-on mount like what you have installed on your trailer. This jack will work great with your existing hardware and…

view full answer...

Answer 2

I have attached a link to a helpful article that explains how to choose the correct winch for a boat trailer. Here is what the article says: Finding the Right Capacity Winch for your Boat Trailer. Boat-size-to-winch capacity is generally 2 to 1 With…

view full answer...

Answer 3

The direct replacement for your Dutton-Lainson 203925B jack would be part #DL22560. According to Dutton-Lainson, the jack would indeed be compatible with your existing mounting plate. I've linked to a product demonstration video featuring the…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Swivel Trailer Jack that Can Fit on 2.5 inch Snap Ring

Product Page this Question was Asked From

Continue Researching