Replacement AC Unit for Duo Therm

Question

Question:

Hello, we have a customer looking for an A/C UNIT that shows to be no longer in production, and would like to see if there is a replacement available. The unit serial # is- 131 31219, model # 6350515.321, product # 991760360- duo therm. Thank you for any help!

asked by: Amber

1

Helpful Expert Reply:

The Advent AC unit part # ACDOM150 will work great as a replacement for a Dometic Duo Therm unit like you have. We had a customer come back and tell us how well this worked as a replacement for a Duo Therm and that no modifications were needed.

expert reply by: Jameson C

1

Review that it fits to replace Duo Therm
(click to enlarge)

Answer 1

If you're wanting to just replace the rooftop unit and still keep the air distribution box and thermostat then you can use the Advent Air Replacement RV Air Conditioner #ACDOM150 you were looking at, but will need to verify the connector type…

view full answer...

Answer 2

The correct replacement for your 300-1406 motor is the Replacement Motor for Lippert Electric Coach Step part #LC301695. If you need other components I would need more info on the steps as this specific motor fits quite a few different steps. If…

view full answer...

Answer 3

For your Parallax 555 model there isn't a converter replacement available. You'd have to replace the entire panel with the part #PD4560K18LS8. It does not come with breakers but in manual all of the required ones are listed from different…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

Not another one! Just kidding Dirk! I was in the Marines I enjoy these conversion questions on the M1101 trailers. I'd be more than happy to list the parts you need, along with quantity, and confirm compatibility. 1 - Timbren Axle-Less Trailer…

view full answer...

Answer 12

Hi Wade, Yes, you’ve definitely got some good options to get away from hand cranking, and I totally get wanting something easier, especially with a cattle trailer. A lot of cattle trailers are gooseneck style and use a square center-mounted jack like…

view full answer...

Replacement AC Unit for Duo Therm

Continue Researching