Do You Offer a 13-1/8" Long Equalizer for 2" Slipper Springs Without any Hardware?

Question

Question:

Can u get ap216 without the bolts etc Just the equalizer

asked by: Bob

0

Expert Reply:

The Equalizer from the Tandem-Axle Trailer Equalizer Kit for 2" Slipper Springs # AP216 is available without the hardware.

The Equalizer for 2" Wide Slipper Springs # TREQ1344 is what you are looking for.

expert reply by: Bud M

0

Answer 1

Hey Colt, You would typically only have shackle straps on one side to allow for the suspension to travel as you roll over bumps in the road. If you'd like to send in some pictures of your setup I can take a look and see if you need to change…

view full answer...

Answer 2

The only reason that I can see that those tabs would have been welded onto your frame is to restrict articulation of the equalizer. And the only reason I would see anyone putting those on is if the articulation was causing the tires to contact the…

view full answer...

Answer 3

Hey Lucas, thanks for reaching out! We have the Equalizer for 2" Wide Slipper Springs #TREQ4541 that looks to match the description you're needing, but this doesn't come in a full-fledged kit because it's from a different…

view full answer...

Answer 4

The equalizer in the Tandem-Axle Trailer Equalizer Kit #AP216 is 11-1/2" on center from the outer spring mounting holes when measuring horizontal separation. One hole will be 6" on center from the equalizer mounting hole center and the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 10

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Do You Offer a 13-1/8" Long Equalizer for 2" Slipper Springs Without any Hardware?

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching