Wheel Hub Bore Size For Trailer Hub and Drum Assembly # 8-407-5UC3-EZ

Question

Question:

What is the minimum wheel hub bore size that will fit this? Need to know if a wheel with a 95.25mm hub bore will fit over this. Thanks in advance.

asked by: Darren N

0

Expert Reply:

The Trailer Hub and Drum Assembly # 8-407-5UC3-EZ is a lug centered hub with a pilot hole size of 3.62". Your 99.25mm(3.75") hub bore wheels will fit on hub/drum.

expert reply by: Bud M

0

Wheel Hub Bore Size For Trailer Hub and Drum Assembly # 8-407-5UC3-EZ
(click to enlarge)

Answer 1

The maximum hub bore measurement for the 5,200 LB or 6,000 LB Dexter hub and drum assembly #8-201-5UC3-EZ is 3.622 inches. So a wheel with center bore of 3-3/4 inches would fit.

view full answer...

Answer 2

In addition to making sure the pilot hole of your wheel is large enough you will also need to measure the bolt pattern of your wheel (see FAQ and video). The bolt pattern of the Dexter Trailer Hub and Drum #8-201-5UC3-EZ is 6 on 5-1/2. I contacted…

view full answer...

Answer 3

I have another option for you, but we do not have a 10" diameter wheel that has the 5 on 4-1/2" bolt pattern and a pilot hole of 3.19". The two 10" wheels that we offer with the 5 on 4-1/2" bolt pattern both have a 2.80"…

view full answer...

Answer 4

A spacer or hub-centric ring is sometimes used on passenger vehicles, but our resident wheel and tire guru tells me that they aren't needed for use on trailers, due to the weight load a trailer wheel will be under. If you feel you need them, you…

view full answer...

Answer 5

Our Provider ST225/75R15 Radial Tire w 15" Viking Aluminum Wheel #A225R6FPS is going to be a great option for you. This wheel and tire includes a 2-year warranty on the tire and lifetime structural defect warranty on the wheel. They also come…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Wheel Hub Bore Size For Trailer Hub and Drum Assembly # 8-407-5UC3-EZ

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching