Is There A 2 Inch Ball That Will Fit The Reese RE94FR Weight Dist Hitch

Question

Question:

I was going to order this hitch but it comes with a 2 5/16 ball and I need a 2”. Am I able to get you guys to put on a 2” before sending to me since you torque it on etc?

asked by: Patrick C

0

Expert Reply:

The 2-5/15" ball on the Reese Pro Round Bar Weight Distribution w Sway Control - Round Bar - 8,000 lbs GTW, 800 lbs TW # RE94FR actually comes pre-installed from Reese. We currently do not have the capacity to change out parts like this on an order, but the Curt 2" Hitch Ball - 1-1/4" Diameter x 2-5/8" Long Shank # C69FR will definitely be a good 2" ball for this system.

expert reply by: Lazer S

0

Answer 1

Hey Mike, so a friction sway control unit like the part #83660 can help stop some of the sway that starts from wind or passing semis but if you are experiencing persistent sway once you hit a certain speed that will only be fixed by increasing the…

view full answer...

Answer 2

The main reason for the price difference is the different construction used for the weight distribution hitches. The Reese Weight Distribution System #RP66540 uses mostly cast parts that are more expensive to manufacture. While the Reese Pro Round…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 6

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hey Michelle! There are definitely a lot of different weight distribution hitch (WDH) options out there. The most important thing is to make sure it is properly rated for the tongue weight of your setup. Looking at the specs for the 2022 Keystone…

view full answer...

Answer 9

Not another one! Just kidding Dirk! I was in the Marines I enjoy these conversion questions on the M1101 trailers. I'd be more than happy to list the parts you need, along with quantity, and confirm compatibility. 1 - Timbren Axle-Less Trailer…

view full answer...

Answer 10

Hey Roger, thanks for reaching out, and congrats on the new camper! For your Silverado and No-Bo 18.2 BeastMode, I really like the Fastway e2 setup. Here is what I recommend: - Fastway e2 Weight Distribution Hitch w/ 2-Point Sway Control - 10,000 lbs…

view full answer...

Is There A 2 Inch Ball That Will Fit The Reese RE94FR Weight Dist Hitch

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching