What Size Fittings for Dexter 23-336-337 Duo Servo Hydraulic Drum Brake Kit

Question

Question:

Does the wheel cylinder take a 3/16 brake line fittings. Dexter 336 and337

asked by: Randall

1

Helpful Expert Reply:

The wheel cylinders on the Dexter # 23-336-337 Duo Servo Hydraulic Drum Brake Kit take a 3/16 fitting, which is typical for trailer brakes.

If you click the provided link, you can see a product description video featuring the drum brake kit.

expert reply by: Mike L

1

Answer 1

As long as your truck's controller has the electric over hydraulic actuator compatibility you won't need to change anything in your truck. If it doesn't there are many options that you can use as a replacement. I recommend the Prodigy P3…

view full answer...

Answer 2

I have a solution for you but no, the Dexter Hydraulic Drum Brakes item #23-336-337 would lock up every time you backed your trailer up. You need free backing brakes like the Dexter Hydraulic Trailer Brake Kit - Free Backing - 12" - Left and…

view full answer...

Answer 3

The Dexter Hydraulic Drum Brake Kit #23-336-337 that you mentioned are Duo-Servo brakes meaning they deliver the same amount of braking whether you are driving either forward or in reverse. The Hydraulic Trailer Brake Kit #AKUBRK-7 that you…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

What Size Fittings for Dexter 23-336-337 Duo Servo Hydraulic Drum Brake Kit

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching