Bearing and Seal Replacement for 2020 Imagine 2250 RK

Question

Question:

What parts do I need to order, Thank You bearings and seals for a 2020 Imagine 2250 rk Travel Trailer by Grand Design

asked by: Ray

0

Expert Reply:

Since we know your 2020 Imagine 2250 rk has 3,500 lb axles the correct bearing kit is the part # BK2-100 which comes with a new seal as well as the correct bearings you'd need.

expert reply by: Jameson C

0

Answer 1

Yes, the Bearing Kit for #84 Spindles part #BK2-100 is correct for a 2018 Grand Design Imagine. This is actually the correct bearing kit for all sub models that use the "120091" 3,500 Lb Axle such as the 2800BH or 2600RB for example. If you…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

Hey Matt, Furrion typically has 4 wires running to their thermostats and the Chill Cube Thermostat #LC74DX is no exception. The harness you see with the thermostat would plug into the Chill Cube's controller and has 4 wires to extra wire to to…

view full answer...

Answer 7

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 8

I sure can BJ. To add a keyless entry lock to your 2025 Airstream, I recommend the Bauer NE RV Entry Door Lock for Trailers item #BA33UR for a left handed lock or item #BA53UR for a right handed lock. These locks have Bluetooth capability and a PIN…

view full answer...

Answer 9

If what you have now Chad is pretty flat at 26 inches then the best replacement size would be 25-1/4 inches like you mentioned. Since you wanted to increase the capacity you would want the part #e57SR which is for 4k trailer axles.

view full answer...

Answer 10

Ron, you’ll be fine with two people. Each Thomas Payne Rest Easy Trifold Loveseat - whether it’s the Dellmead #TP49KR, Driftwood #TP69KR, or McCoy #TP79KR - weighs around 153 pounds, and it ships in two manageable sections (the base and the back), so…

view full answer...

Answer 11

Hey Scott! In order to get you the correct grease cap I am going to need you to take a measurement off of your hubs pilot hole or one of your other center caps. The Grease Cap item #RG04-040 you were looking at has an outer diameter of 1.99".…

view full answer...

Answer 12

You're absolutely right Guy, this is exactly what I would recommend. For a BMW X7 specifically, the Redarc Tow-Pro Link #RED57AR solves a lot of the things people try to avoid with traditional brake controllers: No drilling into the dash No…

view full answer...

Bearing and Seal Replacement for 2020 Imagine 2250 RK

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching