Replacement Upgrade From Power Gear Touch Pad 500210

Question

Question:

my touchpad has a 2 prong that only goes to a jacks down alarm. I am guessing your four prong outlet is the same but where is the wiring harness? I have a 1997 national tropical. and the part number is 500210.

asked by: Derek F

1

Helpful Expert Reply:

To upgrade from your 500210 Power Gear Touch Pad you will in fact need the Replacement Lippert Components Power Gear Manual Leveling Control Kit # LC359259, which comes with a new touch pad, 8-pin harness and 6-pin harness. A 4-pin harness will not be used with this upgrade.

expert reply by: Kyle S

1

click to enlarge

Answer 1

I reached out to my contact at Lippert and he said that both the Keypad 500456 and the 500457 module are obsolete but the Replacement Components Kit #LC359259 will work perfectly to replace both components. This will get your system back up and…

view full answer...

Answer 2

I reached out to my contact at Lippert and he said that it sounds like you have an older Power Gear Manual Leveling kit that had the ground running from the solenoid to the control board. This new kit, part #LC359259, can be used as a replacement but…

view full answer...

Answer 3

Hello again Michael. I'm sorry to say the Power Gear 500456 is an obsolete part. The entire kit #LC359259 is required for replacement to make it compatible with the old system. If you order the #LC82FR on its own it won't work with your…

view full answer...

Answer 4

I found an old wiring diagram for your now discontinued Power Gear 500210 control panel and it really helps show how things are supposed to work. There is a red wire running to the three jacks, the dump valve, and the float valve from the solenoid.…

view full answer...

Answer 5

Are you only installing the #LC82FR (500731)? To replace your 500210 you will need the full kit #LC359259. There are also wiring changes you will have to make at the pump assembly before it will work. After speaking with Lippert it sounds like this…

view full answer...

Answer 6

I do have a solution for you, but since the Power Gear 500457 and 500456 are obsolete you will need to replace the controller and keypad. To do this you'll need the Replacement Lippert Power Gear Manual Leveling Control Kit #LC359259. This will…

view full answer...

Answer 7

I believe you meant to type that your touch pad was part number 500210 which the Replacement Key Pad Control Unit for Power Gear Powered RV Leveling System #LC82FR is a correct replacement for.

view full answer...

Answer 8

There may be a bunch of different reason why your Lippert Level-Up system has suddenly stopped working. The most common reasons are due to a dead battery, extending your jacks too far, or a blown fuse. The first thing you should check for is the easy…

view full answer...

Answer 9

The Replacement Lippert Power Gear Manual Leveling Control Kit part #LC359259 although compatible does not offer plug-in-play installation with some of the older Power Gear leveling systems. Therefore, modifications to the wiring will be needed. I…

view full answer...

Answer 10

The plug that includes the red wire from the Replacement Lippert Power Gear Manual Leveling Control Kit #LC359259 will plug into the back of the control panel and then the other end will plug into the connector coming off of the pump. The other…

view full answer...

Answer 11

According to Lippert, all of the parts in the kit should be used. There are, however, some wiring changes that have been made at the pump assembly for the system to operate. The 6-pin wiring harness that you are referencing plugs into the back of the…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Replacement Upgrade From Power Gear Touch Pad 500210

Continue Researching