Can Self-Adjusting Brake Shoes Be Used On Manual-Adjusting Dexter Brake Assembly?

Question

Question:

Will these pads also fit the non-self adjusting K23-463-00 assembly? Everything looks identical except for the wheel that guides the self adjustment mechanism.

asked by: Martin M

0

Expert Reply:

I do not recommend using the self adjusting brake pads for your manual adjust brake assembly as they are not designed to be used together. If you want the self adjusting setup then you will want to go with Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 10" - Left Hand - 4,400 lbs # K23-478-00 and Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 10" - Right Hand - 4,400 lbs # K23-479-00.

If you want to keep you current Dexter Electric Brake Assembly 10" - Right Hand # K23-463-00 and Dexter Electric Brake Assembly 10" - Left Hand # K23-462-00 then you would want to use one set of Replacement 10" x 2-1/4" Electric Brake Shoes - 1 Brake Assembly # BP04-095 per brake assembly.

expert reply by: Andrew N

0

Answer 1

It sure is Steven. The 5th-Wheel-to-Gooseneck Coupler Adapter Mounting Plate for MORryde Pin Boxes item #MR37ZR is indeed compatible with the Andersen Ultimate Connection 5th Wheel Trailer Hitch System like item #am3200. The Adapter Mounting Plate…

view full answer...

Answer 2

Hey Mark, thanks for reaching out. I can definitely help with that. Does your Explorer already have the factory 4-flat trailer connection? If so, the Curt Echo #C51180 can work great and will require less installation time than really any other…

view full answer...

Answer 3

You need Trailer Hub and Drum Assembly - 4,400-lb E-Z Lube Axles - 10" Diameter - 6 on 5-1/2, part #8-407-5UC3-EZ. This is the hub comes with the bearings, races, and seals. The drum that is compatible is the Dexter Electric Brake Assembly for…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Can Self-Adjusting Brake Shoes Be Used On Manual-Adjusting Dexter Brake Assembly?

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching