Replacement Elbow Fittings for Air Lift LoadLifter 5000 Air Bag System for 2003 Dodge Ram

Question

Question:

I have this kit and am in need of replacement parts that I stripped during my install. Do you offer replacement fittings that are used with the stainless steel lines that come with this kit? I am in need of the AN elbow fittings that threads into the air bag and has the stainless steel line that goes to the air fill valve. I would also like to get another set of the valve that also goes with the stainless steel lines. Help acquiring these parts would be great. Thanks.

asked by: Scott

0

Expert Reply:

It sounds like you're looking for the Replacement Elbow Fitting for Air Lift Ride Control Air Helper Springs - 90-Degree - Qty 1 # AL21837, which are the 90 degree elbow fittings used on the # AL89295. There's a chance that if the elbow fitting stripped that the brass fittings on the bags are also damaged; if this is the case you'll have to replace the bag using the Replacement Air Spring for Air Lift LoadLifter 5000 Ultimate System # AL84293.

expert reply by: Erik B

0

Answer 1

The fitting you're looking for is the Replacement Elbow Fitting for Air Lift Ride Control Air Helper Springs part #AL21848 which matches up with the Air Lift 21953.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Replacement Elbow Fittings for Air Lift LoadLifter 5000 Air Bag System for 2003 Dodge Ram

Products Featured in This Question

Continue Researching