Which Power Lock Conversion Kit Is Correct For Leer Cap With 2 T-Handles?

Question

Question:

Is there an option to convert a 2 t handle rear window to the auto lock? Cap is for a 2018 F150

asked by: Matt K

0

Expert Reply:

Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers # PAL9772 is not a fit for the T handles, however, Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers # PAL9555 would work for your 2018 Ford F150 Leer Cap with two T-handles.

expert reply by: Andrew N

0

Answer 1

You can use 7-way trailer wiring with the module part #PP20-702 to provide power to the third brake light of your camper shell/cap. Basically the stop/turn circuits of the trailer wiring need to run to the yellow wires of this module and then the…

view full answer...

Answer 2

The best product we have for wiring third brake lights on a Leer camper shell is the 3rd Brake Light Logic Module #PP20-702. This will filter out any unwanted signal from the tail lights and allow the 3rd brake light to activate only when the brakes…

view full answer...

Answer 3

Yes, the Pop & Lock Power Lock Conversion Kit #PAL9772 will work on your 2022 Ram 2500 with Leer 100XL truck cap. This kit is confirmed to fit the 2011 and newer Leer 100XL models.

view full answer...

Answer 4

While the Pop & Lock Power Lock Conversion Kit #PAL9772 does tie into your vehicle's power locks and allows it to unlock and lock with key FOB it does not connect to the alarm system in any way so it would not set off the alarm like if…

view full answer...

Answer 5

The Leer 100XR isn't specifically listed by Pop and Lock but more than likely the #PAL9772 will fit. It requires a frameless, bonded glass door with a 1-1/8" center hole for a rotary latch. This particular kit would upgrade your existing…

view full answer...

Answer 6

Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers part #PAL9772 or part #PAL9555 will work on the Leer 100XQ Truck Caps because it uses a cable latching mechanism and the handle is not riveted on.

view full answer...

Answer 7

The wording on that answer is a bit confusing but the solution that will work for your setup is the #PAL9555 since you have the T handles. I sent an update to have the wording clarified on that answer page so thank you for bringing that to our…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Which Power Lock Conversion Kit Is Correct For Leer Cap With 2 T-Handles?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching