Will the Curt Hitch For a 1993 Dodge Ram Fit Models With Roll Pan Bumper

Question

Question:

I have a 1993 Dodge D250 converted to dually. I believe it has what you call a roll pan bumper. Not really a bumper but more of a fascia. The license plate mounts on this. What do I have to modify to make this hitch work? I plan on installing a step bumper in the future. Will that work with this hitch?

asked by: Peter B

0

Expert Reply:

The Curt Trailer Hitch Receiver part # 14001 which is a fit for a 1993 Dodge Ram is designed for models with the factory step bumper. That said, it should work just fine with most roll pan bumpers it would just sit down a little further than normal and may look funky but there would be no functional issues.

expert reply by: Conner L

0

Answer 1

I have attached a link that will show you the trailer hitches that will fit your 1997 Ford F-250 Heavy Duty Pickup with a Standard or Step bumper. All of the hitches on the linked page are designed to fit the larger 37 inch frame. Our most popular…

view full answer...

Answer 2

From side to side, the mounting holes measure 31-1/4 inches apart, center to center. All three sets of holes are the same distance apart. From rear to front, beginning at the rear of the vehicle the distance from the first set of holes to the second…

view full answer...

Answer 3

It looks like you're asking about the B&W Heavy-Duty Trailer Hitch Receiver, part #BWHDRH25122, for your 1996 Ford F-150. You didn't say exactly which dimensions you're looking for but I went out to the warehouse and measured the…

view full answer...

Answer 4

The distance from the front hole to the middle on the #14001 is 5.2". From the middle to the rear hole is 4.04" and from the front hole to the rear hole is 9.2". The distance across for each set of mounting holes is 36".

view full answer...

Answer 5

If your 1989 Ford F-150 has a standard or step bumper AND the frame measures 37-1/4 inches from left to right (outside to outside) then you can use trailer hitch #75038. If your truck has the deep drop bumper then you will need #41504 with adapter…

view full answer...

Answer 6

The Curt #13028 is designed to fit the 1981 - 1987 Chevrolet C/K Series Pickup 6 Foot Bed with Standard or Step Bumper. Assuming everything with the frame is the same as it was from the factory this hitch will line up and fit your 1986 Chevy. It…

view full answer...

Answer 7

I can totally see why that seems like it would help but unless you could ensure that the seal was watertight you'd end up allowing moisture to get into the hitch tube but not able to easily evaporate which would then make potential corrosion even…

view full answer...

Answer 8

When measuring the frame width on a vehicle, you will need to measure from the outside of one frame rail to the outside of the other frame rail. It sounds like you have the 37-1/4 inch frame on your 1983 Ford F-100. The Curt Class IV 2 Inch Hitch,…

view full answer...

Answer 9

I would be happy to and thanks for the pictures! The B&W Heavy-Duty Trailer Hitch item #BWHDRH25122 measures 5.4" from the top of the frame brackets to the top of the receiver and 19-1/2" to the back of the receiver from the last bolt.…

view full answer...

Answer 10

The distance between the mounting bolt holes on the B&W Heavy-Duty Trailer Hitch Receiver #BWHDRH25122 will be 5-3/4" for the closer set and then 11-3/8" for the set that's further apart (see attached photo). All of the hitches we…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Will the Curt Hitch For a 1993 Dodge Ram Fit Models With Roll Pan Bumper

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching