Is Cap of Hydrastar Brake Actuator # HBA16 Vented

Question

Question:

Is the fill cap on the actuator supposed to be vented? On the one im installing now the rubber piece under the cap gets sucked down tight against the fill neck with a lot of vacuum under it. Thanks Thanks

asked by: Jack H

0

Expert Reply:

I spoke with my contact at Hydrastar and he first said that what you are experiencing is totally normal but the cap is not vented and instead the system is vented on the side of it.

expert reply by: Jameson C

0

Answer 1

While we don't have a kit that includes everything for a tandem 5,200 lb trailer we do have all the components separately like the part #K2HR526D for the hubs and rotors. Then for the rest of the components you'd just need the part…

view full answer...

Answer 2

The Kodiak Disc Brakes - 13" Hub/Rotor - 8 on 6-1/2 - E-Coat #KOD54VR will actually not work with torsion axles, however what you can use is the: -Dexter Disc Brake Kit - 12-1/4" Hub/Rotor # K71-635-93. These brakes include 2 e-coated…

view full answer...

Answer 3

Wiring connections for the Electric Over Hydraulic Brake Actuator are as follows. Yellow - Cold side of breakaway switch, The wire that goes hot when a breakaway occurs. Black - Positive connection on breakaway switch, The wire that charges the…

view full answer...

Answer 4

The Dexter DX Series #K71-651 and the Hydrastar Vented Marine #HS381-8067 are more comparable as they both have hardwire installations (just made by different manufacturers) while the Dexter BrakeRite II #T4813102 is more of a…

view full answer...

Answer 5

Thanks for reaching out, Doug! The different between the Marine Hydrastar #HS381-8067 and the Standard Hydrastar #HBA16 is that the Marin version has upgraded marine-grade gaskets and stainless steel hardware so it's better suited for areas where…

view full answer...

Answer 6

Brake parts are manufactured with one of several different finishes - raw metal, e-coat, silver cadmium, or Dacromet or they are made entirely of stainless steel. Parts vary in price and in the degree of resistance to corrosion, depending on the…

view full answer...

Answer 7

Yes, the correct Bearing Buddy to use with the Kodiak Disc Brake kit part #K2HR526D that you have is the part #BB2441SS.

view full answer...

Answer 8

There are a few different 50 amp style connectors. The ones for RV applications use the 240 volt twist lock style of 50 amp outlet (NEMA L6-50) a lot which has three prongs whereas the 120 volt style of 50 amp connector you are thinking of that has 4…

view full answer...

Answer 9

We do have a wiring diagram for you! Whether you have the 1,000 psi Dexter DX Series #K71-650 or the 1,600 psi Dexter DX Series #K71-651 the wiring will be the exact same. I have attached a wiring diagram and review videos for you to check out. Just…

view full answer...

Answer 10

If you already have a breakaway switch and trying to find its power source, It is possible that someone could have wired the breakaway switch directly to the main battery on the trailer but it does not come like that from the factory. The breakaway…

view full answer...

Answer 11

The breakaway system actually must be attached to its own separate battery by law in most states. Therefore, I cannot recommend that you use a seperate, auxiliary battery on the trailer or the vehicle for that matter for the breakaway switch. The…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Is Cap of Hydrastar Brake Actuator # HBA16 Vented

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching