How Do You Disconnect Factory 7-way Connector On 2007 Toyota 4Runner To Install Hopkins HM43374?

Question

Question:

I have no doubts the new ones will plug right in once the old ones are off, but how do I go about disconnecting them? Where do I need to push, pry, or tug to get them to separate?

asked by: Jeramy

0

Expert Reply:

I am happy to help!

To disconnect the factory 7-way connector from your 2007 Toyota 4Runner you will need to press down on the tab of the grey connector, and pry up on the tab on the black connector as shown in the included diagram.

One the factory connector is removed, the Hopkins # HM43374 you were looking at will plug right in.

I included a video review of the # HM43374 for you to take a look at.

expert reply by: Samuel C

0

How To Disconnect Connectors
(click to enlarge)

Answer 1

There is no way to reuse the same bolt holes that held on the OEM 7-way with the new Hopkins Plug-In Simple Vehicle Wiring Harness for Factory Tow Package #HM43374 on your 2008 Toyota 4Runner. You can drill new holes if you wish to reuse the factory…

view full answer...

Answer 2

Since you are seeing the electrical overload only when pressing the manual override, it sounds like your vehicle wiring is supplying more than 12V power to the Echo #C51180. If this is only happening when you use the manual override, then goes back…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

How Do You Disconnect Factory 7-way Connector On 2007 Toyota 4Runner To Install Hopkins HM43374?

Featured Help Information

Miscellaneous Media

Continue Researching