Will the AirLift LoadLifter 5000 Fit On a 2011 Ford F-250 with OEM Prep Package

Question

Question:

Does the AL88396 fit a 2011 f250 cclb diesel with the factory gooseneck and fifth wheel prep package?

asked by: Jake

0

Expert Reply:

Yes. The AirLift # AL88396 are a confirmed fit on your 2011 Ford F-250 with the OEM Prep package installed; it can also be used with aftermarket 5th wheel and gooseneck systems.

I've linked a short review and installation video of these airbags for you to check out, as well.

expert reply by: Erik B

0

Answer 1

Yes, suspension enhancements such as the SumoSprings Helper Springs and the Air Lift LoadLifter Air Helper Springs will help to minimize vehicle sag. They do this by transferring the pin weight of the trailer more towards the front of the vehicle…

view full answer...

Answer 2

For your 2011 F250 super duty 4x4 lariat with a 6.7 turbo diesel 3/4 ton I would still recommend the part #F2597. The part #AL88396 that you referenced has a note that it will only work with universal gooseneck or fifth wheel install kits. Because of…

view full answer...

Answer 3

If you have a 4-wheel drive and the fifth wheel frame brackets are installed on the outside of your 2015 F-350 frame rails, and the hole in the frame is open as the attached drawing shows. then the Air Lift suspension system that will work is part…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Will the AirLift LoadLifter 5000 Fit On a 2011 Ford F-250 with OEM Prep Package

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching