Can 10 x 2-1/4 Inch Electric Trailer Brakes be Used in Place of 10 x 1-1/2 Inch Brakes
Updated 04/13/2013 | Published 04/11/2013 >
Products Featured in This Question
Question:
Will these 10x2.25 assemblies interchange with 10x1.5 assemblies on Dexter 3000 pound axles on my 2010 Passport travel trailer? The 10x1.5 shoes seemed to wear out prematurely. Thanks
asked by: Kent W
Expert Reply:
You will need to measure the width of the inside of the drum where the pad makes contact with the drum to determine if you can go to the wider 10 x 2-1/4 inch assemblies. If you cannot then you would also need to change out the hub and drum. To do that I would need to know the inner and outer bearing numbers stamped into the metal of the bearings.
If the hub is wide enough then you can use the 10 x 2-1/4 inch assemblies # 23-27 for the right side and # 23-26 for the left.
It is also possible that the brakes you have are adjusted more aggressively than they need to be. To determine if the brakes are properly adjusted, turn the hub in the direction of travel. You should be able to turn it, if you cannot then the brakes are too tight. If you can turn the hub you want to be able to hear a slight but constant dragging of the pad on the drum.
I have linked a video showing the adjustment process. fast forward to the 4:40 minute mark to see the adjustment process.
Product Page this Question was Asked From
Dexter Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Shop: Dexter Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3.5K
- Q&A: Solution for Needing Replacement Parts for Atwood Levelegs
- Article: Most Popular Wheel Bearings
- Search Results: exact slide motor
- Shop: Replacement Trailer Wheel Bearing - L68149 - Qty 1
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Lippert Hub and Drum Assembly - 8,000-lb Axles - 12-1/4" Diameter - 8 on 6-1/2 - Pre-Greased
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer hitch
- Q&A: Who Makes The Best Quality Trailer Bearings?
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Trailer Wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: trailer tires and wheels
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Video: etrailer Electric Trailer Brakes Review
- Search Results: trailer jack
- Shop: Brake Controller
- Search Results: trailer lights
- Video: Let’s Check Out the Dexter Electric Trailer Brake Assembly
- Article: Breakaway Kit Installation for Single and Dual Brake Axle Trailers
- Shop: Gooseneck Hitch
- Search Results: trailer brakes


