Will the Draw-Tite Hitch for a 2018 Ford EcoSport Fit the SES

Question

Question:

Will the Hitch you installed on the SE also fit the SES since the muffler is located underneath in back and not side of car. I just ordered it and realized you were installing on SE not SES. Please advise.

asked by: DONNA S

0

Expert Reply:

The Draw-Tite Trailer Hitch Receiver part # 36660 is a fit for all models of a 2018 Ford EcoSport which included SE, SES, etc. It features a bolt-on install with no cutting or drilling required. It has a class II rating with 1-1/4" receiver tube opening.

expert reply by: Conner L

0

Answer 1

You are correct that for your 2021 Ford EcoSport there are two trailer hitch receiver options, the Curt #C12188 and Draw-Tite #36660. These hitches are very similar as they both share a similar design meaning they have roughly the same installation…

view full answer...

Answer 2

The main difference between the Curt Hitch #C12188 and the Draw-Tite Hitch #36660 for your 2021 Ford EcoSport is that the Curt is assembled here in the United States while the Draw-Tite is installed overseas. Other than that difference, there are a…

view full answer...

Answer 3

The Draw-Tite Trailer Hitch Receiver #36660 will fit your 2018 Ford EcoSport SE no matter what size engine you have so you are good to go on that end of things (plus the EcoSport in the video is an SE). The hitch comes will all of the hardware to get…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 8

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey George, for your 2026 Toyota RAV4 Hybrid we have the Curt hitch part #C34FR62ZY as a confirmed fit but it's on a little bit of a backorder at the moment which is why you don't see any hitch options in our fitguide. The hitches from…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Will the Draw-Tite Hitch for a 2018 Ford EcoSport Fit the SES

Continue Researching