How to Remove a Threaded Bearing Buddy That is Stuck
Updated 05/24/2021 | Published 05/20/2021
Question:
I recently bought a used boat trailer with Bearing Buddies. The hubs appear to be oil hubs have threaded to add oil that have been converted to grease using Bearing Buddies. I am trying to pull the hubs to grease the bearings and replace the seals but I cant get the Bearing Buddies off. Do all oil hubs have threaded dust caps? I can turn the Bearing Buddy using a pipe wrench a little bit but they will not turn off. I can get it to rock back and forth using a hammer but not very far. Not sure if these are threaded or pound on. Its on a 2006 Prestige boat trailer. Thanks.
asked by: RON F
Expert Reply:
The vast majority of oil bath style hubs will indeed be threaded. These are also notorious for getting pretty stuck after a while. What you will need to do is spray some WD-40 all the way around it after being loosened as much as you can. Let that sit and then tighten, and back off. This may need to be done a few times to break up whatever it is that it is getting hung up on.
Product Page this Question was Asked From
Bearing Buddy Bearing Protectors - Model 2441T-SS - Threaded - Stainless Steel - Qty 2
- Trailer Bearings Races Seals Caps
- Caps
- Bearing Protector Grease Cap
- 2.32 Inch
- 5200 lbs Axle
- 6000 lbs Axle
- Bearing Buddy
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hub and Drum Assembly - 3,500-lb Axles - 10" Diameter - 5 on 4-1/2 - Pre-Greased
- Search Results: brake drum
- Q&A: Troubleshooting Trailer Wiring that When Connected Vehicle Beeps and Says Check Wiring
- Q&A: Is Load Range Important When Replacing Trailer Tires on a Popup Camper
- Shop: Replacement B&B RV Twist-On Gravity Water Fill Cap Wiith Strap - Black
- Shop: Replacement Cap with Strap for Valterra Gray Water Waste Valve - 1-1/2" FPT - Black
- Q&A: How To Tell What Size Bearing Buddy Is Needed for My Trailer Hubs
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Article: How to Measure for Trailer Hitch Drop
- Search Results: trailer tires and wheels
- Q&A: Comparing Kenda KR03, KR35, And KR53 Tires
- Shop: Trailer Wheel Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Shop: Trailer Wiring
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Video: Hands-On with the Hub Saver Hub and Wheel Protector
- Shop: Suspension Enhancement
- Q&A: Best Suspension Upgrade for 33" Tandem Axles: Road Armor vs Dexter EZ Flex for Ember 22ETS
- Search Results: trailer wiring
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Brake Controller
- Q&A: What is the Best Grease for Trailer Bearings
- Search Results: trailer jack
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Article: Trailer Lighting Requirements
on Trailer Bearings Races Seals Caps
