Replacement Foot for Lippert Powered Stabilizer

Question

Question:

Im looking for a replacement foot/arm assembly for a Limpert PSx1 stabilizer.

asked by: Marc W

0

Expert Reply:

For your Lippert powered stabilizer we have a replacement foot with the part # LC157584. The arm/leg that comes down that the foot attaches to is not available as a separate item.

expert reply by: Jameson C

0

Answer 1

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Answer 2

The first thing I recommend doing is checking the trailer and the tow vehicle connection. Often times there can be issues with corrosion build up. It never hurts to check and clean the connection. I would also check all of your ground connections and…

view full answer...

Answer 3

You'll want to keep your 205/75-14 Load Range C tires fully inflated to the 50 psi pressure rating listed on the sidewall. The tires will only have the stated capacity when fully inflated. If they are not fully inflated, the tire's load…

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 6

It can indeed be used if the jack leg can accommodate the 1-1/4 inch width beetween the mount ears as shown in the provided photo. If the leg is too wide to fit in between the ears, they might fit inside the leg is the inside of the leg is greater…

view full answer...

Answer 7

Hey Edward, thanks for reaching out. Without knowing the exact light model, I can't say exactly where the release points are, but most of those older oblong RV porch/utility lights use a snap-on lens rather than screws through the face. Look…

view full answer...

Answer 8

Hey Jim. The Replacement Foot Assembly item #LC157584 is the correct one you need for the Lippert PSX2 power stabilizer. I checked with Lippert and the base measures 5.88" x 5.88". This will be an exact replacement for the one in your…

view full answer...

Answer 9

Hey Scott, thanks for reaching out. At this time, we offer only one size for the Lippert Schwintek Slide-Out System part #LC34VC, and I'm sorry to say we don't have a dimensional diagram for that one. What I can tell you is the 62-5/8"…

view full answer...

Answer 10

Hello Jerry, Thank you so much for the pictures, they are always most helpful! I am sorry but there is not a seal packing kit, you will need to replace the entire jack. For your Lippert Level Up with part number 343315-RA, you will want the…

view full answer...

Answer 11

Hello John, Making the switch over to the SmartPlug is a smart idea =) On the fitment side, yes, the SmartPlug #SM67FR inlet will fit your trailer. SmartPlug inlets are designed specifically to replace the standard RV twist-lock shore power inlet and…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Replacement Foot for Lippert Powered Stabilizer

Product Page this Question was Asked From

Continue Researching