Can I Fit the Yakima JayLow on Yakima HD Bars

Question

Question:

Will these fit on yakima hd cross bars?

asked by: Matt

1

Helpful Expert Reply:

Yes, you can fit the Yakima JayLow # Y04073 on Yakima HD bars but you will need to use the clamps that come with the JayLow and not the T-slot adapters.

expert reply by: Erik B

1

Answer 1

The Yakima JayLow Kayak Carrier, part #Y04073, can actually carry two kayaks on its own. The only additional thing needed to carry your second kayak on your 2018 Audi A4 Allroad is another set of straps, like etrailer's Cam Buckle Cinch Straps,…

view full answer...

Answer 2

Once installed, the only portion of the Draw-Tite #DT68MR Class III hitch that will be visible from the rear is the receiver tube and the safety chain loops as you can see in the photo I fetched from the instructions. You will need to do some…

view full answer...

Answer 3

I'd start by making sure that your 7 way didn't get disconnected from the US car connector it's plugged into. If a fuse was blown, it would normally only effect the circuit that it's tied to, so I don't believe that would be the…

view full answer...

Answer 4

If you mean the length of the bars from side to side on the Thule Xsporter ladder rack #TH500XT they are 72 inches. If you mean the width front to back of an individual bar they are 3-5/8 inches wide and 1-3/4 inches tall.

view full answer...

Answer 5

There are a couple of differences between the two. The JetStream bars like #Y00425 are made of extruded aluminum while the CoreBars such as the #Y00421 you've looked at are constructed of galvanized steel. As you've mentioned, the CoreBar has…

view full answer...

Answer 6

The Yakima JayLow Kayak Carrier w/ Tie-Downs #Y04073 doesn't have a T-Slot adapter but they do fit crossbars with max dimensions of 3-1/2" x 1-11/16". Since the Yakima HD Crossbars like the 68" #Y01158 only measure 3" wide x…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Can I Fit the Yakima JayLow on Yakima HD Bars

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching