Do Both Upper Bolts of Lippert Tandem Axle Lift Kit part # LC407131 go Through Spacer

Question

Question:

Its hard to tell from the instructions. Do both of the upper mounting bolts go thru the spacer or just the lower bolt?

asked by: Scott R

0

Expert Reply:

Yes both of the upper bolts of the Lippert Tandem Axle Lift Kit part # RR23QX go through the spacer like you mentioned.

expert reply by: Jameson C

0

Answer 1

The Dexter Trailer Springs Over-Under Conversion Kit part #K71-384-00 CAN be used with slipper springs. However, the process of installing this kit on a trailer with a set of slipper springs is more in depth than installing this kit on a trailer with…

view full answer...

Answer 2

Since one end of a slipper spring is suspended instead of bolted to a hanger or shackle strap the Dexter Trailer Springs Over-Under Conversion Kit part #K71-385-00 and other likes them are considered unsafe for slipper springs. The only other option…

view full answer...

Answer 3

Hey Alex, if you don't mind swapping your drop axle to a straight axle that would be a great way to gain the additional height over using an over under kit. That would be a lot more expensive than a over under kit part #K71-384-00 so keep that in…

view full answer...

Answer 4

The recommended minimum clearance between gooseneck trailer overhang and truck bed rails is 4-6 inches. I'd recommend 6 inches but a lot of people get by with just 4. Ideally you have at least 6 inches of clearance and the trailer is sitting…

view full answer...

Answer 5

The trailer fuse locations for a 2021 Ram 2500 can be found either in your owner's manual or on the underside of the fuse box lid. I have attached them for you below as well. F28 20 Amp Blue – Trailer Tow Backup Lights F29 20 Amp Blue – Trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...