Does the Curt TruTrack 10K Weight Distribution System Come with 2-1/2" Shank

Question

Question:

Hello, Can I purchase this with a 2.5inch shank ? if so what is the item # Thank you

asked by: RAYMOND R

0

Expert Reply:

The Curt TruTrack 10K Weight Distribution System part # C17500 does not come with a 2-1/2" shank. Therefore, you can either use an adapter or you ca purchase another shank separately like the Curt Weight Distribution Shank part # C17131.

expert reply by: Conner L

0

Answer 1

Yes you can! All of our WD shanks, including the Curt #C17121 that you referenced, are compatible with other WD systems. The part where the head of your WD sits is 2" wide and the mounting holes are 1-1/4" apart on center. I have attached a…

view full answer...

Answer 2

Hey Anthony! The shank that comes with your part #BLU75FR hitch gives you up to 2.75 inches of drop, so if your new Ram 2500 sits higher and your trailer’s nose is pointing up, that’s probably not enough. I recommend the 12" shank Blue Ox part…

view full answer...

Answer 3

Hey Paul, thanks for reaching out! Yes, the Blue Ox TrackPro Weight Distribution Shank #BLU74ER will work with the Curt Dual Ball Attachment #C69NR. Let me know if you have any other questions!

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Does the Curt TruTrack 10K Weight Distribution System Come with 2-1/2" Shank

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching