Replacement Surge Brake Actuator for Reliable ACT-7.5K Brake Actuator

Question

Question:

I am looking for a replacement coupler for a Reliable ACT-75K disc brakes with lockout. It is on a Mastercraft trailer w/swing tongue.

asked by: Brad S

0

Expert Reply:

I have a replacement for you but we do not carry the Reliable ACT-7.5K Brake Actuator. We have the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout # DX89FR that will replace your surge brake actuator on your trailer. The specs match but the bolt holes may not line up so you likely will need to drill new holes.

expert reply by: Jacob H

0

Answer 1

We don't have any replacement parts available to fix your Reliable ACT 7.5k actuator but if you've got drum brakes you can use the Titan Brake Actuator with Manual Lockout - Bolt On - Drum - 2" Ball - 7,500 lbs Item #T63FR which comes…

view full answer...

Answer 2

I do have a full replacement for you but we do not offer replacement parts for the Reliable ACT-7.5K Brake Actuator unfortunately. For a full replacement, the best option we have for you is the Swing-Away Actuator w/ Electric Lockout part #T4839100…

view full answer...

Answer 3

Typical torque rating for car, truck and SUV lugs is 90 ft. lbs. As always, you should check with the manufacturer of the mobile home for proper ratings. Vehicle weight, lug type, hub type, etc. all play a role in the torque rating and the best way…

view full answer...

Answer 4

The only difference between the Replacement Inner Member for Dexter DX7.5L Actuator part #DX99FR and part #DX39FR is that the former is for tandem axle trailers with disc brakes and the latter is for single axle trailers with disc brakes or tandem…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Replacement Surge Brake Actuator for Reliable ACT-7.5K Brake Actuator

Product Page this Question was Asked From

Continue Researching