Height of Bulldog and the Powered-Drive Trailer Jack, # BD500187, from Bracket to Top of Jack

Question

Question:

What is the overall height from the mounting plate to the top of the jack on the Bulldog BD500187 ?

asked by: Gary P

0

Expert Reply:

I spoke with my contact at Bulldog and the Powered-Drive Trailer Jack, # BD500187, measures 20-1/2 inches from the mounting bracket to the top of the jack. I have included a picture showing this measurement for you.

expert reply by: Michael H

0

click to enlarge

Answer 1

The Electric Jack w/ Footplate and 7-Way Plug #EJ-3527-BBX that you referenced has a height of 20-1/2 inches from where it mounts to your trailer frame to the top of the jack.

view full answer...

Answer 2

The design of the Progressive Dynamics 4000 Series Mini RV Converter #PD4045KA hasn't changed much, but the key is to look for the converter section. The switch is located on the converter's circuit board and will have in white "LA"…

view full answer...

Answer 3

The Replacement Spring Loaded Pull Pin #BD500388 is currently the only spring loaded pull pin that I see available for round jacks. It has only been confirmed to fit the Bulldog Powered Drive Trailer Jack #BD500199 which mounts to a 2" diameter…

view full answer...

Answer 4

I checked with Bulldog and they confirmed that the Replacement Spring Loaded Pull Pin #BD500388 will work on the Bulldog Powered-Drive Trailer Jack #BD500187 .

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Height of Bulldog and the Powered-Drive Trailer Jack, # BD500187, from Bracket to Top of Jack

Continue Researching