Can The BAKFlip FiberMax Hard Tonneau Cover Be Used In More Than One Position When Folded Back?

Question

Question:

Does BAKFLIP model 1126133 tonneau cover lock down in more than one position when folded back. IE, can it be used covering only 1/3 of the bed with 2/3 open?

asked by: Bill T

0

Expert Reply:

Yes, the BAKFlip FiberMax Hard Tonneau Cover - Folding - Aluminum and Fiberglass # BAK1126133 can be used in various fold positions. I have attached a couple photos for you to check out which show the cover being used in the 1/4 and 2/4 positions. This bed cover is confirmed to fit your 2020 Chevrolet Silverado 2500 with 6-3/4' bed.

A few neat features that the BAKFlip FiberMax has to offer are the low-profile design and the weather-proofing system. It is only 1/2" thick, so it will be very sleek and will not look bulky on the back of your truck. The weather-proofing system consists of heavy duty seals running along the bed cover. There is also a built-in drainage system to help keep water out of the bed.

expert reply by: Andrew N

0

BakFlip Cover Folded In 1/4 Position
(click to enlarge)

BakFlip Cover Folded In 2/4 Position
(click to enlarge)

Answer 1

Hey Brian, this is a great question. Not one we very often but the Leer Quad Fold part #LE67FR has really narrow rails that attach to the inner side of your bed rails so that would give you the least amount of affected turning clearance for your 2025…

view full answer...

Answer 2

Hi JD; if I had to choose between the Leer Hard Tonneau Cover #LE67FR and BAKFlip MX4 #BAK448133 I would go with the MX4. As far as security goes both are locking covers so it will be about the same between the two. The MX4 has seals and drain tubes…

view full answer...

Answer 3

Hey Randy, yes the Leer quad fold tonneau part #LE67FR that its your 2020 Chevy Silverado short bed will allow you to use your fifth wheel hitch when folded up but not all the way against the rear window. With that last panel folded down you'd…

view full answer...

Answer 4

For a 2024 Chevy Silverado 2500 with a 6-3/4' bed I have two recommendations depending on whether you'd like a hard top or soft top. For the hard top I recommend the Lomax Hard Tonneau Cover #LO79FR. For the soft top I recommend the TruXedo…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Can The BAKFlip FiberMax Hard Tonneau Cover Be Used In More Than One Position When Folded Back?

Continue Researching