Difference in Class I and Class II Ball Mounts and Can They Interchange
Updated 02/21/2013 | Published 02/16/2013
Products Featured in This Question
Question:
Is the draw bar different for a class 1 and class 2 receiver? I mean, will they fit interchangeably? In particular the 1-1/4inch drawbar and hitch.
asked by: Andrew W
Expert Reply:
The correct ball mount or draw bar for the Hidden Hitch Class I 1-1/4 Inch Hitch, part # 24812, on your 2010 Toyota Matrix will be Draw-Tite Ball Mount, part # 3593.
When towing with a Class I or Class II trailer hitch, the ball mount that is recommended by the hitch manufacturer should be used. All Class I and Class II trailer hitches are tested and rated with the specific ball mount for that hitch. Using a ball mount that is not recommended by the manufacturer will void the warranty.
A Class II ball mount will not fit into a Class I hitch. Manufacturers accomplish this by placing a stopper in the back of Class I hitch receivers so that drawbars and accessory shanks can only slide into the trailer hitch opening up to that point. On hitch accessories designed for Class II trailer hitches, the shank that slides into the hitch opening is longer. When this longer shank slides into a Class I hitch, it will hit the stopper, preventing the pin hole on the hitch from lining up with the pin hole on the accessory. This is done to prevent somebody from overloading a Class I hitch.
I am including links to FAQ articles on hitch receiver sizes and the different hitch classes.
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Article: Trailer Hitch Receiver Sizes
- Shop: Brake Controller
- Video: In-Depth Review of the Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes
- Video: An In-Depth Look at the etrailer Ball Mount w/ Pre-Torqued 2" Ball
- Video: Checking Out the etrailer Ball Mount w/ Pre-Torqued 2" Ball
- Video: Complete Breakdown of the Curt Drawbar for 1-1/4" Hitches
- Shop: Curt Drawbar for 1-1/4" Hitches - 5-3/8" Rise, 6" Drop - 5-9/16" Long - 2K
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 2" Hitch - 2" Drop - 7,500 lbs
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 1-1/4" Hitch - 3-7/8" Rise - 3,500 lbs
- Shop: Hollywood Racks Sport Rider SE Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount
- Shop: etrailer Ball Mount w/ Pre-Torqued 2" Ball - 2" Hitch - 2-3/4" Rise - 7,500 lbs
- Shop: Curt Fusion Ball Mount for 2" Hitches - 2" Ball - 2-1/4" Rise - 7,500 lbs
- Shop: Curt RockerBall Shock Absorbing 2" Hitch Ball - 3/4" Diameter Shank - Chrome - 3.5K
- Search Results: trailer hitch ball
- Shop: Vehicle Tow Bar Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Search Results: trailer hitch
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Trailer Wiring Diagrams
- Video: Clean Up Your Trailer Wiring
- Search Results: trailer wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch ball mount
- Article: How to Measure for Trailer Hitch Drop
- Video: The Low-Down on the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: Suspension Enhancement
on Trailer Hitch
