Dual Fan Setup that Can Move 3,750 CFM that is 24 inch by 17 inch

Question

Question:

hello can you make a dual fan set up 24in x 17 x 3.5 puller 3750. cfms or close too my measurements ?

asked by: Rick W

1

Helpful Expert Reply:

We have a dual fan setup that is VERY close to what you are looking for but is 1 inch deeper than what you mentioned with the part # D16833. This is rated for 3,750 CFM, is 24 inches wide, 17 inches tall, and 4-1/2 inches deep.

If the depth is an issue you could maybe look into relocating your radiator to accommodate it. Otherwise we aren't aware of anything similar that is 3-1/2 inches deep.

expert reply by: Jameson C

1

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 6

Hey Kirt, Congrats on the new car! To get your car safe to flat tow you'll need the following parts: Base-Plate #RM39FR Tow-Bar Adapter #RO64FR Lighting #RM-15267 Chargeline #RM-156-25 Air-Force One Vehicle Side #SM99209 and Hose #SM99666 (if you…

view full answer...

Answer 7

Unfortunately we do not have a video of the HappiJac Truck-Mounted Camper Tie-Downs #LC184089 being installed. The Rear anchors are installed in the end of the bumper. There is no precise mounting location since a variety of bumpers may be installed.…

view full answer...

Answer 8

I do have an option for you though we don't carry the exact same style of wheel the trailer came with from the factory. That said, it's just a spare wheel after-all so you don't really need an exact style match since it won't even be…

view full answer...

Answer 9

Yes, there is Ken. You can install the Derale 32 inch High-Output, Electric Radiator Fan-and-Shroud Assembly - 4,000 CFM, item #D16934. It is designed as a universal application so you'll need to measure to be sure there is room to mount the…

view full answer...

Answer 10

I do have have an option for you but there is not an electric OEM fan replacement available for the 4.2L engine unless you go with a universal electric fan like part #D16831 that is a bit more cost effective than the Flexalite. As long as you have…

view full answer...

Answer 11

Each of the fans of the Flex-a-lite Dual 13-1/2" Electric Radiator Fans w/ Shroud #FLX295 can flow up to 2,300 CFM. Also worth mentioning is that the likelihood of one of the fans failing is very low.

view full answer...

Dual Fan Setup that Can Move 3,750 CFM that is 24 inch by 17 inch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching