Correct Spare Wheel/Tire for Magic Tilt Trailer Model CA1928W

Question

Question:

Im looking for a spare wheel/tire combo for a magic tilt trailer, model ca1928w. Will your item AM32153 fit? it is a 14 inch 5 hole x 4.5 pattern. It appears by my measurement, with the wheel mounted, that the hub opening is 3 1/4 inches in diameter

asked by: Bennett F

0

Expert Reply:

Yes, the Karrier ST205/75R14 Radial Trailer Tire with 14" White Wheel part # AM32153 will fit a Magic Tilt Trailer Model CA1928W. If you need a carrier we have plenty of options like the CE Smith Spare Tire Carrier part # CE27202.

expert reply by: Conner L

0

Answer 1

Hey David, thanks for reaching out. That torque spec will depend on the wheel type. For a 1/2" lug nut on a 15" steel wheel the torque spec is 90-120 ft-lbs. For aluminum wheels like the #KE64JV you were looking at it's 90-100 ft-lbs. I…

view full answer...

Answer 2

Hello Bailey, thanks for reaching out. It may be possible to go with the larger 15" tires. The main thing to consider is the clearance in the wheel well area. You want at least 3" between the tire and the fender, and at least 1"…

view full answer...

Answer 3

Hello Greg, Thank you for the rotor measurement, it was most helpful as it tells me you have a 2K axle. Tie Down Engineering is no longer, but Kodiak parts work great! The Calipers are different for the driver and passenger side: - Driver Side:…

view full answer...

Answer 4

I sure do Brian and thanks for the information! To add a spare tire mount to your Magic Tilt tandem axle boat trailer, I recommend the Tie Down Spare Tire Mount item #TD86FR. It attaches to frames and tongues up to 8" tall. The Tie Down item…

view full answer...

Answer 5

You're right, the mounting bracket is unique (in a good way) for the Curt TriFlex NEXT Trailer Brake Controller #C24VV. The bracket is smaller and all you do is put the included adhesive tape on the bracket and stick it wherever you like under…

view full answer...

Answer 6

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 12

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...