Hardware Needed With the Road Armor Equalizer Kit

Question

Question:

I have a 2020 Puma 255rks fith wheel, just need to know if this is the right setup with the 3 1/8 in wet bolt kit? I just want to be sure Im ordering the right stuff. Plug and play so to speak. Thanks!

asked by: Mark T

0

Expert Reply:

When using the Road Armor Shock Absorbing Equalizer Kit # LC696740, for bolts you want ten 9/16" suspension bolts part # ABS34FR and 8 shackle straps per axle. The kit you are talking about which is part # LC64FR has the correct parts from Lippert, but not enough of them. The correct shackle straps also depends on your trailer.

If you let me know what length your shackle strap is I can recommend those too. The most common size for the type of trailer you have is a 2-5/8 inch shackle strap like # 115052. I also linked below our selection of shackle straps.

expert reply by: Evangeline M

0

Answer 1

You will need a lock nut, though the ones you mentioned are not, we do have the correct lock nut for the Step Bolt For Double Eye Springs - 9/16" Diameter - Plain - 3" Long #ABS34FR: - Fastenal Lock Nut - Zinc Plated Steel - 7/16"-20…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Answer 9

Hey Jon; I was actually just talking to Furrion about heat options for the Chill Cube yesterday (1/21/2025). At this time, the only way to have heat with this unit is through a furnace on a ducted setup. The Furrion Chill Cube RV AC w/ Air…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Hardware Needed With the Road Armor Equalizer Kit

Products Featured in This Question

Featured Help Information

Miscellaneous Media

Continue Researching