The Dimensions For The TorkLift GlowStep When Folded Up In The Stored Position

Question

Question:

On the tla7843 what is the product dimensions folded up? I want to see if they fit in my empty generator compartment.

asked by: Tony K

0

Expert Reply:

The dimensions of the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear - 3 Steps - 375 lbs - White Bracket Item # TLA7843 folded up are going to be 11-1/4" deep x 25" wide x 13" high.

expert reply by: Shane H

0

Answer 1

I have a solution for you, but the TorkLift #TLA7843 require much more mounting space than you've got available on your 2020 Palomino SS1240. Because of the limited mounting space under your door, you'll need to use something similar to the…

view full answer...

Answer 2

While we do not have a video of these steps being specifically installed on your camper I took a look at the instruction manual, which is also linked, and there is a method for installing these steps on a camper that does not have a bumper. You would…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 5

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hey Bob, congrats on a setting up a new camper! Out of all of those options you'll also need to consider daily driving comfort unless that camper is a permanent addition to your truck bed. Listed below are a brief breakdown of each and a…

view full answer...

Answer 10

Hi Lance, I completely understand where you’re coming from on this. You can use your factory hitch with a 48 inch extension like part #TLE1648, so you don’t have to jump to the dual receiver setup right away since this extension is designed to work…

view full answer...

Answer 11

Hello Dennis, That is definitely something you will want to check with your setup. The B&W Continuum #BW78FR will sit about 9 inches below your trailer frame once installed, so you will want to measure from the ground to the bottom of the frame…

view full answer...

Answer 12

Hey Jack, yes the Torklift camper tie downs part #TL63PR are the correct set for your 2024 Ford F-350 Tremor with a short bed and factory hitch. The turnbuckles part #TLS9526-2 that you referenced as well would be a great set that matches what you…

view full answer...

The Dimensions For The TorkLift GlowStep When Folded Up In The Stored Position

Product Page this Question was Asked From

Continue Researching