Replacement Caster Wheel for 1-3/4" Tube

Question

Question:

Hello, I am looking for a trailer caster wheel that will fit a 1 3/4 or 1.75 tube. Do you have one available? Thanks

asked by: Dan K

0

Expert Reply:

It sounds like you are looking for a caster wheel for a trailer jack. If that is the case then we do have some options like the Ram Removable Assembly part # JC-101 for a 2" outer tube and 1-3/4" inner tube.

expert reply by: Conner L

0

Answer 1

Sounds like you need the Replacement Caster Wheel for Ultra-Fab Manual 2" Trailer Jack #UF49-954035. This is designed to fit both the 2" jack as well as the 1-3/4" tube like what you have. Attached is a review video for you to check…

view full answer...

Answer 2

Taylor, you can use the Replacement Caster Wheel for Ultra-Fab Manual 2" Trailer Jack #UF49-954035 which will work with 2" and 1 3/4" jack tubes.

view full answer...

Answer 3

The Replacement Caster Wheel for Ultra-Fab Manual 2" Trailer Jack - Qty 1 #UF49-954035 is designed to fit the Ultra-Fab jacks 49-954030 and 49-954032 which have an inner tube diameter of 1-3/4 inches, so this wheel should work for your jack as…

view full answer...

Answer 4

Hey Marius, there isn't a wheel available for the etrailer electric jack part #EJ-3527-BBX that you referenced which is pretty normal for electric jacks. The reason is the wheels end up cutting the capacity of the jack by about a third and most…

view full answer...

Answer 5

The Removable Wheel, #DL22414, was designed to be used with the Dutton-Lainson 1,000 lb A-Frame Trailer Jack, #DL22530, which has an inner tube / down tube diameter of 1-3/4 inches so this may work for you. This wheel is intended to be held on to the…

view full answer...

Answer 6

Yes, the Replacement Caster Wheel #UF49-954035 that you referenced is compatible with trailer jack inner tubes that measure 1-3/4" in diameter. This is verified in the attached review video.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 12

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Replacement Caster Wheel for 1-3/4" Tube

Product Page this Question was Asked From

Continue Researching