Replacement Hub for 2500 lb Trailer Axle with 5 on 5.5 inch Bolt Pattern

Question

Question:

L44649 L68149

asked by: John F

0

Expert Reply:

Are you sure it's a 2,500 axle and not a 3,500? The 2500 isn't a standard one so we'd need to get bearing numbers/spindle dimensions to identify it.

expert reply by: Jameson C

0

John F.

12/22/2020

L44649 L68149

Jameson C.

12/22/2020

Thanks! Based on that you'd want the part # AKIHUB-555-35-K for if you need idler hubs or part # 84557UC3 for if you need a hub/drum.

Answer 1

We do not have a grease seal with this particular combination of inner and outer diameters. We have seals with both inner diameters you provide, and seals with the same outer diameter, but not both. If you took your measurements from the old seal,…

view full answer...

Answer 2

I may have a solution for you, but we do not have any hubs that are compatible with the #LM48548 inner bearing that you've currently got in your hubs. Additionally the #84556UC3 is not going to fit your spindle because the #L68149 outer bearing…

view full answer...

Answer 3

I would be happy to. I took your information and listed the replacement parts next to it. Inner bearing: 2.362 OD, 1.375 ID, .470 thick. is the Timken Replacement Trailer Wheel Bearing - LM48548 item #TMK79FR and the Timken LM48510 Replacement Race…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Trailer wheel bearings are specific to the spindle that is installed on the axle that is on your trailer. You will need to safely support the trailer, remove the wheel and tire, remove the grease cap, remove the cotter pin and washer that secures the…

view full answer...

Answer 12

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Replacement Hub for 2500 lb Trailer Axle with 5 on 5.5 inch Bolt Pattern

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching